金刚石磨头粒度对SiCf/SiC复合材料磨削性能及失效行为的影响

Impact of diamond grinding head grit size on grinding performance and failure behavior of SiCf/SiC composites

  • 摘要: 为揭示磨头粒度对SiCf/SiC复合材料磨削性能与工具失效行为的影响机制,采用100目、200目和300目金刚石磨头开展单因素磨削对比试验。通过采集磨削力信号,结合激光共聚焦扫描显微镜和扫描电镜观测,系统分析磨头目数对磨削力动态演变、表面粗糙度、表面形貌特征及磨头磨损特征的影响规律。结果表明,在满刀磨削阶段,磨削力随目数增大呈上升趋势,且高目数磨头力值随磨削进程持续增大;不同于传统金属加工中磨头目数对粗糙度的显著影响,不同目数磨头磨削表面粗糙度Sa均维持在约3 μm,但相比100目磨头,300目磨头磨削可获得更平整的表面。此外,磨削表面近边缘区域纤维细观断裂形貌呈明显各向异性:沿进给方向纤维断口多呈破碎状,垂直进给方向纤维断口则相对整齐,这种差异主要与近边缘区磨粒瞬时切入轨迹及纤维局部受力模式的耦合相关,而非单一由宏观进给方向决定;磨头失效机制具有显著的粒度依赖性,100目磨头因高冲击载荷及强轴向振动共同诱发棱角处磨粒脱落,而200目与300目磨头则以切屑堵塞为主要失效形式。

     

    Abstract: To elucidate the influence mechanism of grinding head grit size on the machining performance and tool failure behavior of SiCf/SiC composites, single-factor grinding experiments were conducted using 100-grit diamond head, 200-grit diamond head and 300-grit diamond head. By acquiring grinding force signals and combining observations from confocal laser scanning microscopy and scanning electron microscopy, the effects of grit size on grinding dynamics, surface roughness, surface morphology characteristics, and tool degradation were systematically investigated. The results indicate that the grinding force increased with grit size during the full-contact stage, with the force values of finer grits exhibiting a continuous upward trend over the grinding duration. Unlike traditional metal machining where grit size significantly affects surface roughness, the surface roughness Sa in this study remained stable at approximately 3 μm across all grit sizes; however, the 300-grit diamond head yielded a smoother and more uniform surface texture compared to the 100-grit diamond head. Furthermore, obvious anisotropy is observed in the fine-scale fiber fracture morphologies near the edge region of the ground surface: fibers aligned along the feed direction predominantly exhibit brittle, fragmented fractures, whereas those oriented perpendicular to the feed direction present relatively neat fracture surfaces. This difference is mainly related to the coupling between the instantaneous cutting trajectories of abrasive grains and the local load modes acting on the fibers, rather than being determined solely by the macroscopic feed direction. The tool failure mechanisms demonstrate significant grit size dependence: under combined high impact loads and intense axial vibration, the 100-grit diamond head is more prone to grit detachment at the edges of chip flutes, while 200-grit diamond head and 300-grit diamond head are dominated by chip clogging as the primary failure mode.

     

/

返回文章
返回