column
Residual useful life prediction of rolling bearings based on multi-dimensional temporal mixing features
WAN Zhongyi, WU Kaiping, XU Bin, WANG Congyu, ZHOU Jiang
2025(2): 9-16. DOI: 10.19287/j.mtmt.1005-2402.2025.02.001
Abstract PDF
Research on fault diagnosis method of rolling bearing based on LCLSABO-KELM
LIANG Shan, QI Bing, LI Hao, LIU Jun, WANG Kai, WANG Jun
2025(2): 17-22. DOI: 10.19287/j.mtmt.1005-2402.2025.02.002
Abstract PDF
Fault diagnosis of rolling bearings based on WOA-VMD and PSO-SVM
YANG Yuanpeng, CHEN Zhigang, YU Zhihong, WANG Yanxue, CHEN Longqiao
2025(2): 23-29, 42. DOI: 10.19287/j.mtmt.1005-2402.2025.02.003
Abstract PDF
Adaptive variable impedance control methods in dynamic environments
LIU Yu, CHANG Zhiyuan, LI Ke, CHU Hongyu, ZHANG Xiaoqiang, SHAO Yanhua
2025(2): 30-35. DOI: 10.19287/j.mtmt.1005-2402.2025.02.004
Abstract PDF
Time optimal trajectory planning of the 6R manipulator based on improved particle swarm optimization
WANG Maixin, YAN Li, LI Yufei
2025(2): 36-42. DOI: 10.19287/j.mtmt.1005-2402.2025.02.005
Abstract PDF
Improved A* path planning algorithm based on stochastic map
LIN Shuo, JIN Hengjiang, HAN Zhonghua, ZHAO Jianming
2025(2): 43-47. DOI: 10.19287/j.mtmt.1005-2402.2025.02.006
Abstract PDF
Research on fast path planning and hand-eye calibration of6DOF robotic arm
SUN Chao, HU Zhiming, PENG Linyi, YE Zian, DING Jianjun
2025(2): 48-56. DOI: 10.19287/j.mtmt.1005-2402.2025.02.007
Abstract PDF
Analysis of influencing factors of grinding surface residual stress in spiral bevel gear based on grey relational theory
CHANG Jibao, ZHANG Fengshou
2025(2): 57-64. DOI: 10.19287/j.mtmt.1005-2402.2025.02.008
Abstract PDF
Research on the influence of groove curvature radius (osculation) on the fatigue life of four contact point ball bearings
YAO Jinchi, YU Changxin, WEI Yangang, LYU Haiting, LI Dongju
2025(2): 65-71. DOI: 10.19287/j.mtmt.1005-2402.2025.02.009
Abstract PDF
Influence of oil-water emulsion on gear elastohydrodynamic lubrication characteristics
ZHOU Kaihong, CHEN Dengshan
2025(2): 72-80. DOI: 10.19287/j.mtmt.1005-2402.2025.02.010
Abstract PDF
Research on optimization design of focused ultrasound assisted laser processing system
WANG Xu, REN Kun, LIU Yi, DAI Longjie, WANG Jin, LIU Guoliang
2025(2): 81-89. DOI: 10.19287/j.mtmt.1005-2402.2025.02.011
Abstract PDF
Simulation and microstructure of Y2O3 enhanced TC4 alloy welding laser cladding
WEI Jiashuai, SHI Mingquan
2025(2): 90-98. DOI: 10.19287/j.mtmt.1005-2402.2025.02.012
Abstract PDF
Research progress in crystal plasticity deformation mechanisms and their numerical simulation methods
ZHAO Shuai, WANG Sujuan
2025(2): 99-107. DOI: 10.19287/j.mtmt.1005-2402.2025.02.013
Abstract PDF
Sliding mode position control of precision direct drive system based on fuzzy disturbance observer
LI Dongbo, LI Xu, LIU Haibo, WANG Yongqing
2025(2): 108-115, 128. DOI: 10.19287/j.mtmt.1005-2402.2025.02.014
Abstract PDF
High-efficiency machine tool service matching in cloud manufacturing mode based on two-stage approach
XIE Xun, ZHOU Lirong, WANG Liming, KONG Lin, CHEN Zihan, ZHANG Chuanwei
2025(2): 116-128. DOI: 10.19287/j.mtmt.1005-2402.2025.02.015
Abstract PDF
Research on the maximum torque per ampere control of brushless doubly- fed machine servo system
QI Yan, WANG Nannan, LIU Heqiang, XIAO Bo, ZHOU Xuepeng, WEI Ning, YU Guangxu, ZHANG Yin
2025(2): 129-136. DOI: 10.19287/j.mtmt.1005-2402.2025.02.016
Abstract PDF
A design and application of a special turn-milling production line for thread processing at the end of injection-screw
PAN Xiaomin, JIN Yangyang, XIE Ruimu
2025(2): 137-143. DOI: 10.19287/j.mtmt.1005-2402.2025.02.017
Abstract PDF
Prediction of surface roughness in contour milling and optimization of process parameters for efficiency enhancement
GAO Yi, TANG Yuanbin, HUANG Xiaoyan, LU Juan, MA Junyan
2025(2): 144-153. DOI: 10.19287/j.mtmt.1005-2402.2025.02.018
Abstract PDF
Research on frame production scheduling optimization based on the fusion of NSGA-II and red fox algorithm
CAO Zhehan, LI Feng, ZHOU Xueliang, LIU Zijia
2025(2): 154-163. DOI: 10.19287/j.mtmt.1005-2402.2025.02.019
Abstract PDF
Research on electrochemical machining process of variable cross-section micro-array pit
XIAO Chengjun, KUANG Shuaiwei, LI Junfei, WANG Zeneng, CHEN Weili, ZHANG Yongjun
2025(2): 164-170. DOI: 10.19287/j.mtmt.1005-2402.2025.02.020
Abstract PDF
Multi-objective optimization of tire dynamic balancing machine spindle based on response surface method
LIU Lifu, FENG Xianying, LI Peigang, SONG Wenfei, SUN Xiaoping
2025(2): 171-176, 193. DOI: 10.19287/j.mtmt.1005-2402.2025.02.021
Abstract PDF
Product quality prediction method based on residual correction
CHEN Xinhang, XU Xinsheng, CAO Li, WU Songze, LU Hongyi
2025(2): 177-184. DOI: 10.19287/j.mtmt.1005-2402.2025.02.022
Abstract PDF
Improved YOLOv8-based method for detecting non-compliant behaviors of workers in smart factories
HE Jihua, ZHANG Yuefeng, LIU Yueyun
2025(2): 185-193. DOI: 10.19287/j.mtmt.1005-2402.2025.02.023
Abstract PDF
Research on integrated grinding force modeling of particle distribution in grinding area
FU Yu, ZHANG Chunzhi, LIU Haihua, MA Chenxiang, MENG Xiangyi
2025(2): 194-199. DOI: 10.19287/j.mtmt.1005-2402.2025.02.024
Abstract PDF